How do you change the mode on a hot tub?

The procedure for switching from one mode to another is different depending on the type of keypad installed on your hot tub. Keypads without a “Mode” button. Press “Temp”, then “Light” to switch to the next mode. Repeat the process until you reach the mode that you’re looking for.

Moreover, how do you change the mode on a Balboa hot tub?

Mode is changed by pressing the Temp or Set button, and then pressing the Light button. If there are UP and DOWN buttons, use the UP button. Do not press the buttons at the same time. It’s one button, release, and then the other button.

Secondly, how do I get my hot tub out of sleep mode? I have seen this happen with Cal Spas. On them you need to press the ‘TEMP’ button and then the ‘LIGHT’ button within three seconds of each other and this will change the modes from EC (economy mode), to SL (sleep mode) and finally to ST (standard mode) which is what you want.

Keeping this in consideration, what does economy mode mean on a hot tub?

The modes are explained below: Standard. The temperature of the hot tub will be reach & maintained when in standard mode. Economy. The hot tub will only use the heater when the spa is in “filter mode” and the water has encountered a drop in temperature below the standard thermostat setting.

How do you turn the temperature up on a Balboa hot tub?

To change the set temperature, press a temperature button again before the display stops flashing. Each press of “Warm” or “Cool” will adjust the set temperature. After three seconds, the display will stop flashing and begin to display the current spa temperature.

What is sleep mode on hot tub?

SLEEP mode heats the spa water to within 20 degrees of the set temperature during the filter cycle. For example, if your spa is set for 100 degrees, on sleep mode it will heat to 80 degrees and stop. Sleep mode is displayed as SL or SLP on your topside control.

What does SLP stand for on a hot tub?

Even though the pump runs all the time, there will still be hidden “filtration cycles” programmed in your hot tub control system. Sleep (SLP or SL) This mode allows the temperature to drop to 20°F (11°C) below the thermostat set point.

How long does it take for a hot tub to warm up?

about 4 hours

What does f4 mean on a hot tub?

Spa Side Error Codes
OH Overheat Protection (Heater is deactivated, pumps low speed is activated).
SN Flow Switch (heater is deactivated. Pump may also be deactivated).
F2 Panel sensors have been pressed too many times in a short period of time.
F4 Circuit Board temperature has exceeded acceptable limit.

How do I reset my hot tub control panel?

You can reset a hot tub control panel by switching it off, waiting for between 10 and 20 seconds and then switching it back on again. If the error signal continues on the control panel then you will need to consult your hot tub manual to see what the problem is.

What temperature should I keep my hot tub when not in use?

What is the right hot tub temperature when not in use? A rule of thumb is that the temperature should be at least 5 degrees lower than when in use. It is necessary to keep it at lower temperatures when it’s not in use so that energy consumption isn’t too high.

What temperature should a hot tub be set at in the summer?

If you have your hot tub temperature is set at its maximum safe 104 degrees, you shouldn’t soak more than 15 minutes. At lower summer water temperatures, you can linger longer. Kids younger than 12 enjoy lower temperatures.

How long should I run my hot tub filter?

How Long Each Day Should I Run My Spa Filter? Most spa filter cycles are pre-set to run twice each day for four hours each time, but allowing the spa to cycle less often can save energy. Washington State University’s energy program recommends running the filter twice a day for three hours.

What does EC code mean on hot tub?

Ecn or Ec is Alternating with Temp: The Spa is Operating in the “Economy” (Ecn or Ec) Heating Mode. The Water Temperature is sampled Only during Programmed Filter Cycles. The Heater will only operate and Heat up to Set Temperature during the Filter Cycles.

Who makes evolution hot tubs?

2. Evolution Spas – manufactured by Strong Spas, in Northumberland Pennsylvania. The Strong brand is well known amongst independent hot tub dealers across the country and more so on the east coast where it has a more dominant presence.

What setting should my hot tub be?

The majority of hot tub users prefer a water temperature in the range of 100°F-102°F. 104°F is the standard maximum temperature, which some users also prefer. Always consult a physician before getting in the hot tub while pregnant.

What temperature should you keep your hot tub in the winter?

Ideal Spa Temperature for Winter

Many spa owners prefer to keep their spa temperature between 102°F and 104°F, though even 100°F is safe and comfortable for a healthy adult.

What is priming mode on a hot tub?

The purpose of the priming mode is to manually activate each spa pump prior to the automatic heat cycle being started. Typically cycling each pump a few times will prime or purge any air from that pumps plumbing.

What does Dr mean on my hot tub?

Newer hot tubs have a digital display for error codes that can assist with troubleshooting. A message such as “dr” or “dry” or “heater dry” is a warning that there’s no water in the heater tube. If the water is low, add water to the proper level and try restarting the pump and heater.

What does HL mean on hot tub display?

system shut the heater down

Why is my hot tub says dry?

DR or DRY. If not enough water—or worse, none—is traveling through your heater when it kicks on, it can cause what’s known as a dry fire where the heating element is damaged. This commonly occurs when your water level is too low. Topping of your hot tub may be the only solution necessary.

How do you prime a Balboa hot tub?

Using the control panel:

Turn the spa on and wait for PR (Priming Mode) to appear on the topside display. Press the JETS button to turn on the pump and let it run for 10 seconds. The pump should be running in low speed. Press the JETS buttons again and let the pump run in high speed for 10 seconds.